diff --git a/include/configs/lx2160ardb.h b/include/configs/lx2160ardb.h
new file mode 100644
index 0000000..67d214d
--- /dev/null
+++ b/include/configs/lx2160ardb.h
@@ -0,0 +1,102 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2018 NXP
+ */
+
+#ifndef __LX2_RDB_H
+#define __LX2_RDB_H
+
+#include "lx2160a_common.h"
+
+/* Qixis */
+#define QIXIS_XMAP_MASK			0x07
+#define QIXIS_XMAP_SHIFT		5
+#define QIXIS_RST_CTL_RESET_EN		0x30
+#define QIXIS_LBMAP_DFLTBANK		0x00
+#define QIXIS_LBMAP_ALTBANK		0x20
+#define QIXIS_LBMAP_QSPI		0x00
+#define QIXIS_RCW_SRC_QSPI		0xff
+#define QIXIS_RST_CTL_RESET		0x31
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
+#define QIXIS_LBMAP_MASK		0x0f
+#define QIXIS_LBMAP_SD
+#define QIXIS_RCW_SRC_SD           0x08
+#define NON_EXTENDED_DUTCFG
+
+/* VID */
+
+#define I2C_MUX_CH_VOL_MONITOR		0xA
+/* Voltage monitor on channel 2*/
+#define I2C_VOL_MONITOR_ADDR		0x63
+#define I2C_VOL_MONITOR_BUS_V_OFFSET	0x2
+#define I2C_VOL_MONITOR_BUS_V_OVF	0x1
+#define I2C_VOL_MONITOR_BUS_V_SHIFT	3
+#define CONFIG_VID_FLS_ENV		"lx2160ardb_vdd_mv"
+#define CONFIG_VID
+
+/* The lowest and highest voltage allowed*/
+#define VDD_MV_MIN			775
+#define VDD_MV_MAX			855
+
+/* PM Bus commands code for LTC3882*/
+#define PMBUS_CMD_PAGE                  0x0
+#define PMBUS_CMD_READ_VOUT             0x8B
+#define PMBUS_CMD_PAGE_PLUS_WRITE       0x05
+#define PMBUS_CMD_VOUT_COMMAND          0x21
+#define PWM_CHANNEL0                    0x0
+
+#define CONFIG_VOL_MONITOR_LTC3882_SET
+#define CONFIG_VOL_MONITOR_LTC3882_READ
+
+/* RTC */
+#define CONFIG_SYS_RTC_BUS_NUM		4
+
+/* MAC/PHY configuration */
+#if defined(CONFIG_FSL_MC_ENET)
+#define CONFIG_MII
+#define CONFIG_ETHPRIME		"DPMAC1@xgmii"
+
+#define AQR107_PHY_ADDR1	0x04
+#define AQR107_PHY_ADDR2	0x05
+
+#define CORTINA_NO_FW_UPLOAD
+#define CORTINA_PHY_ADDR1	0x0
+#define INPHI_PHY_ADDR1		0x0
+
+#define RGMII_PHY_ADDR1		0x01
+#define RGMII_PHY_ADDR2		0x02
+
+#endif
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM	           0
+#define CONFIG_SYS_I2C_EEPROM_ADDR	           0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	    1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS     3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/* Initial environment variables */
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
+	"scriptaddr=0x80800000\0"		\
+	"kernel_addr_r=0x81000000\0"		\
+	"pxefile_addr_r=0x81000000\0"		\
+	"fdt_addr_r=0x88000000\0"		\
+	"ramdisk_addr_r=0x89000000\0"		\
+	"loadaddr=0x80100000\0"			\
+	"kernel_addr=0x100000\0"		\
+	"ramdisk_addr=0x800000\0"		\
+	"ramdisk_size=0x2000000\0"		\
+	"fdt_high=0xa0000000\0"			\
+	"initrd_high=0xffffffffffffffff\0"	\
+	"kernel_start=0x21000000\0"		\
+	"lx2160ardb_vdd_mv=800\0"		\
+	"mcmemsize=0x40000000\0"
+
+#include <asm/fsl_secure_boot.h>
+
+#endif /* __LX2_RDB_H */